![]() |
Programmable ignition KIT for FIAT500 - 126 (VAT are not included - TAX free for extra-UE countries) |
![]() |
|
HVD3
&
ERREERRE
Project present
PROGRAMMABLE IGNITION KIT for FIAT 500 & FIAT 126 |
![]() |
|
|
KIT
composed by: |
|
€ 550
(iva esclusa)
|
|
Why I'll should install this KIT on my FIAT500 engine? Spark advance is necessary for the proper functioning of the motor and it's different depending of the number of engine revolutions but also the pressure in the suction mainfold. A system of ignition advance based only on engine rpm (centrifugal masses, variable capacitors, etc..) cannot recognize the different engine operating conditions and therefore will not be able to make it work to the best of its potential. A programmable ignition system based on rpm and pressure in the duct will be capable of operating the engine with the proper ignition advance for maximum mechanical performance in any conditions. Benefits that I get with KIT? Once you set the correct map for the type of engine (displacement, carburetor affects the map in advance), the benefits are more apparent during the transition have the ability to "stretch" of the engine. This translates into an engine rpm ready to go-up more speed and ability to "pull" a little more gears without have a sharp decline in power at high rpm. The best overall mechanical performance of the engine finally determines a decrease in fuel consumption. What else can I get? The kit comes complete with software to configure the unit. You can save how many maps you want and load them according to different needs.
|
||
|
Caratteristiche tecniche: |
|
|
|
||
|
|
||
|
What happens during the combustion? Although the phase of combustion is defined as "burst phase" in reality, the combustion occurs in a gradual spread from the spark throughout the combustion chamber. During the combustion energy (chemistry) contained in the fuel is converted into energy (heat) that goes in part to increase the temperature of the gases that are inside the cylinder, and part is transmitted to the metal walls that surround the volume within combustion occurs. A rise in temperature of the gas causes a pressure increase of the gas through the surface piston and the rod is transformed into mechanical energy for the motion of the vehicle. The pressure will increase gradually until reaching a peak after which starts to decline. For maximum mechanical performance of the engine, the peak should occur around 20 ° after the piston has reached the point of maximum travel exceeding PMS (in literature is also common to find 20 ° ATDC, which means 20 ° After Top Dead Cilinder). What is the "spark advance"? The petrol engines are also called "command ignition engine" because the point at which combustion begins is determined by the management system of spark (pins, distributor, ECU or other). The combustion phenomena described above, takes time (a few milliseconds) to be completed, so to ensure that the peak of maximum pressure is about 20 ° ATDC (maximum efficency), it is necessary that the combustion starts with a certain advance of the PMS itself. This time is called "spark advance" What influences on anticipating ignition? In first approximation we consider that the combustion occurs at constant speed. The "time available" to combustion, will be gradually decreasing according to increase of number of engine revolutions per minutes cause piston travels faster. So, certainly "increases the number of turns per minute", spark advance should be changed to have peak pressure on piston surface around 20 ° ATDC. In reality the speed of combustion is not constant but is influenced by many factors including "pressure in the suction pipe". For the latter parameter is true that the more high is initial pressure and higher is the burn rate and consequently the spark advance should be reduced. During the march, we can have at same rmp, pressure in mainfold are very different. For example if we are going to accelerate at 3000 rpm with throttle all open, we have a high pressure. If we are at 3000 rpm at constant speed, throttle probably will be at 50% and the pressure will be much lower. More at 3000 rpm during release, we have a very low pressure in maifold cause the throttle are closed. In these different conditions, the engine should work with diferent spark advance values.
|
||